How To Sync Adjustable Bed Remote

Are you looking a solution for how to sync adjustable bed remote? then you are in the right place.

In this article, I am going to show you how to sync your Adjustable Bed Remote effortlessly.

Having an adjustable bed in your home is like having a personal oasis of comfort.

With just one touch you can enhance your sleeping experience and Syncing your Adjustable Bed Remote is the key to unlocking this comfort oasis.

So without wasting time let’s dive into the solution and learn to pair the adjustable bed remote.

How to Sync Leggett and Platt Adjustable Bed Remote

To program your Leggett and Patt adjustable remote follow the steps mentioned below.

Programming remote to 1 base

• First, plug the base into the power outlet.
• Then take your remote and press and hold the Head down and Foot up buttons.

• Now while holding these two buttons hold the PAIR button located on the power cord of your bed.

• Hold all these three buttons until you hear a beep sound.
• After you hear a beep sound release all these buttons and your remote is now paired with your bed.

Now test whether all the buttons of your remote are working or not.

Note- If the pair button is not working then you can use the learn button instead of the pair button present on the control box. To find the control box you need to tilt the bed to its side.

Programming 1 remote to 2 bases

• Plug both bed bases into the power outlet.
• Now control each base with its remote to ensure that both bases are working properly.
• After that use each base remote and lower bases to the flat position.
• Now unplug both the bases from the power source.
• Now tilt both the bases to its side place them near to each other and get a Sync cable.

• Now locate the control box under the bed and take the Sync cable.
• After that plug one end of the sync cable into the sync port (on the control box) of base 1.

• Plug the other end of the cable into the sync port (on the control box) of base 2.
• Now Turn both bases over onto their legs. (Carefully and take care that the sync cable doesn’t come out from the sync port)
• Plug both bases back into the power outlet.

That’s it now you can use your single remote to control both bases.

How to Sync Nectar Adjustable Bed Remote

To program your Nectar adjustable bed remote with base follow these steps.

• First, unplug the base from the power outlet and wait for 30 seconds.
• After 30 seconds Plug it back in the power source.
• Now carefully tilt the bed to its side and locate the control box.
• On the control box, there is a pair button press that pair button twice and wait for the LED on the control box to turn blue.
• Now take your remote and press and hold the pair button on the remote the light on the remote flashes and starts the pairing process.
• If the pairing process is successful the light on the control box turns green.

If the pairing fails the LED on the control box turns off. then you need to repeat the process.

How to Sync Tempur-Pedic Adjustable Bed Remote

To pair your Tempur Pedic adjustable bed remote follow the steps mentioned below.

To pair Ergo PROSMART Base

• First, take your remote remove the battery compartment cover, and locate the pair button inside that.

• Now Unplug the power cord from the power outlet and wait for 1 minute.

• After 1 minute plug it back in the power source.
• Now the Soundbar will provide the verbal cue ‘Bluetooth Mode’ to indicate it is ready for pairing.
• Perform the next step within the 10 seconds after this.
• Press and hold the PAIR button on the back of the remote
• Now the the PAIR button will illuminate and start to flash.
• When the PAIR button stops flashing Soundbar will provide the verbal cue ‘Connected’ to indicate the remote has paired successfully to the control box
• After this release the pair button and your remote is now paired with the base.

To pair Ergo 1.0 | Ergo Power Base | Ergo Smart Base, Ergo Extend 1.0 | Ergo Extend Smart Base

• First, locate the battery box under the bed and press the button present on the box twice.

• After that, A light on the Battery Back Up Box will illuminate.
• Now take your remote open the remote battery compartment and locate the pair button.
• Then press and hold the pair button and the pair button will illuminate and a blue light start flashing.
• Now wait for the pair button to stop flashing and the light on the battery backup box to go away.
• Once the pair button stops flashing and the battery box light goes away release the pair buttons.

Your remote is now paired with your adjustable bed.

How to Sync Serta Adjustable Bed Remote

To Sync Serta adjustable bed remote follow the steps mentioned below.

• First Locate the Power Down Box under the base of the bed.
• Now double click on the button present on the power down box.
• After this take your remote open the back side of the remote and press and hold the pair button near the battery compartment.
• The light on the remote will begin to flash and become a continuous light.
• Now wait for the light of the power down button and the remote to go off.
• Once the light goes off release the buttons and your remote is paired now.

If the Button on the power down box is not available then Press the Reset button on the control box. You can locate the control box under the base of the bed.

The Pairing LED light on the control box will illuminate then follow the above steps.

How to Sync Split King Adjustable Bed Remote

To sync your Split King adjustable bed remote follow the steps mentioned below.

• First, unplug the bed from the power supply and wait for 1 minute.
• After 1 minute plug it back again into the power supply.
• Take your remote remove the battery cover and locate the pair button near the battery compartment.
• Now locate the control box under the base of the bed.
• Then press the button twice present on the control box and the light will illuminate.
• After this press and hold the pair button on the back of the remote and the remote light will begin to flash.
• Now wait for the light of the remote and control box to go off and then release the button.

Your remote pairing is complete.

How to Sync Casper Adjustable Bed Remote

Follow the steps mentioned below to sync your Casper adjustable bed remote.

• First, unplug the bed from the power source and wait for 1 minute.
• After 1 minute plug it back into the power source.
• Now locate the control box under the base of the bed and press and hold the link button until the LED on the control box turns on.

• After this take your remote and press and hold the head up and Foot up button and the remote’s backlight starts flashing.
• Now wait for the remote LED and control box LED to stop flashing.
• Once these lights stop flashing release the remote buttons and your remote is paired.

How to Sync Ease Adjustable Bed Remote

To sync your Ease adjustable bed remote follow these steps

• First, unplug the bed from the power source then wait for 1 minute and plug it back.
• Perform the next step within the 10 seconds after this.
• Take your remote open the battery compartment and press and hold the pair button.
• The pair button is present near the battery compartment.
• After pressing the pair button will illuminate and start to flash.
• When the pair button stops flashing release the pair button

To pair Ease 1.0 | 2.0

• First, locate the battery box on the bed and press the button present on the battery box twice.

• After that, A light on the Battery Back Up Box will illuminate.
• Now take your remote open the remote battery compartment and locate the pair button.
• Then press and hold the pair button and the pair button will illuminate a blue light starts flashing.
• Now wait for the pair button to stop flashing and the light on the battery backup box to go away.
• Once the pair button stops flashing and the battery box light goes away release the pair buttons.

How to Sync Richmat Adjustable Bed Remote

To sync your Richmat adjustable bed remote follow the steps mentioned below.

• First, unplug the bed from the power supply, and then after 1 minute plug it back.
• Now locate the blue pair button on the cord from the power supply (which could be zip-tied to the bottom of your bed).

• After this take your remote and press and hold the Foot up and Head up buttons and at the same time hold the blue button with the other hand.
• After 5 seconds or so it should beep after this release all these buttons.

Your remote is paired now.

If the head-up and foot-up combination doesn’t work then you can try out the head-down and the foot-up button while pressing the reset coding button located on the control box.

How to Sync Structures Adjustable Bed Remote

To pair your Structures adjustable bed remote follow the below-mentioned steps.

• First, unplug the bed from the power supply then wait for 1 minute and plug it back.
• Within 10 seconds press and hold the head up button and foot up button until the LED light on the control box flashes.
• Once the light stops flashing release these buttons and your remote is ready to use.

Info – The control box is located under the base of the bed.

How to Sync Motion Air Remote

To pair your motion air adjustable bed remote follow the below-mentioned steps.

• First, unplug the bed from the power source then wait for 1 minute and plug it back.
• Perform the next step within the 10 seconds after this.
• Take your remote open the battery compartment and press and hold the pair button.
• The pair button is present near the battery compartment.
• After pressing the pair button will illuminate and start to flash.
• When the pair button stops flashing release the pair button

Your remote is paired now.

How to Sync Beautyrest Remote

To pair your Beautyrest remote follow the steps

• First, unplug the bed from the power source then wait for 1 minute and plug it back.
• Perform the next step within the 10 seconds after this.
• Take your remote open the battery compartment and press and hold the pair button.
• The pair button is present near the battery compartment.
• After pressing the pair button will illuminate and start to flash.
• When the pair button stops flashing release the pair button

How to Sync Milemont Adjustable Bed Remote

To pair your Milemont adjustable bed remote follow the steps mentioned below.

• Plug the bed power cord into the power supply.
• Now locate the blue pair button on the power cord.
• After this take your remote and hold the Head lift and Foot lift buttons together along with the blue pair button.
• Hold these three buttons together for 5 seconds until you 2 beep sounds.
• After this release, all these buttons and your remote is now paired.

How to Sync Mattress Firm Adjustable Bed Remote

To program your Mattress firm adjustable bed remote follow the steps mentioned below.

• First, unplug the bed from the power supply and wait for 3 minutes.
• After 3 minutes Plug it back into the power supply.
• Now locate the control box under the base of the bed.
• Then check on the control box the Pairing light should be on.
• If it is not on then use and pointy thing and press the reset button twice.
• Now the pairing light should be on once the light is on take your remote press and hold the head up and Flat button.
• Hold these two buttons until the pairing light on the control box goes off.

Your remote is now ready to work.

The adjustable Bed Remote not working

There are two main reasons for your not working adjustable bed remote.

Child lock

The child lock is a feature of an adjustable bed remote when activated it makes the remote button inactive to prevent any accidental button pressing.

If your bed remote isn’t working, check if the child lock is activated.

To identify whether the child lock is activated or not in your remote.

When you press any function key of the remote lights blink but do not respond to your command.

Dead batteries

The dead or old batteries could be a possible reason for your not working remote.

So if your remote batteries are too old consider replacing them with a fresh pair of batteries.

FAQ

Can I adjust my Sleep Number bed without the remote?

Yes, you can use your smartphone to adjust the sleep number bed without a remote.

Do adjustable beds need maintenance?

yes to maintain the optimal function of the bed, some maintenance is required, such as lubricating and retightening certain components.

Conclusion

That’s it for this article.

I hope this article helps you in syncing your adjustable bed remote.

If you have any doubts or suggestions related to this article please let me know in the comments.

Thank you